image
Book a Demo to Save up to 17% on Measurement Reports, Unlock FREE ProData Reports, SmartQuotes™, Material Lists, and Receive a $25 Gift Card -   Click to Schedule Your Demo Today

Gutter Measurement Software for Contractors: Footage, Fittings, and Downspouts in One Report

4 minute read

https://roofscope.com/image/cache/catalog/2025/2026/B18-header-1200x628-812x387.png

written by RoofScope published on 11. 05. 2026

A gutter bid comes down to two lists. The first is how many feet of gutter and downspout the house needs. The second is how many fittings it takes to cap, turn, and drop every run. Get either one wrong and you're making a second trip to the supply house or eating the overage.

Gutter measurement software gives you both lists from aerial imagery, along with a waste table and a drawing of every run. It also leaves one decision with you: gutter size and profile.

What does a gutter measurement report include?

Every GutterScope report opens with project totals:

  • Total length: gutter and downspout combined, in linear feet

  • Gutter: linear feet of gutter

  • Downspout: linear feet of downspout

  • Endcaps: count

  • Inner corners and outer corners: counts (your miters)

  • Elbows: count, on every report

Under the totals sits a waste-factor table. It applies 4% through 15% to the total length, one row per percent, so you can read the padded footage straight off the page.

The second page is a dimensioned plan view. It shows where each gutter run sits on the structure, where the corners and endcaps fall, and where the downspouts drop, with each downspout labeled by story height. GutterScope also covers properties with more than one structure.

Page one of a GutterScope report showing gutter and downspout totals, fitting counts, and a waste factor table.

What a real GutterScope report shows, line by line

The sample report for 11 Advantage Ave, a residential property, totals 471.5 linear feet: 309.5 feet of gutter and 162.0 feet of downspout. The fittings come to 18 endcaps, 3 inner corners, 2 outer corners, and 33 elbows.

Those six lines are the core of a gutter material list. You've got the footage to order, plus every piece that ends, turns, or drops a run.

Read the plan view next to the totals. The totals tell you how much to order. The drawing tells your crew where it goes: which runs meet at an inside or outside corner, which runs end in a cap, and where each downspout comes off the gutter. When a corner count looks high or low for the house, the drawing is where you check it.

Order quantities are still your call. The report gives you measured lengths and counts. How you buy stock, how you seam runs, and what you keep on the truck stay with you.

GutterScope plan view drawing showing gutter runs, corners, endcaps, and downspout locations by story height.

What does the report leave to the contractor?

A GutterScope report gives you length and fittings. It doesn't specify gutter size or profile. Whether a job calls for 5-inch or 6-inch, K-style or half-round, is your call, made when you walk the job.

Plan for that the same way you do today. Use the report for the takeoff, and confirm size and profile on site before you write the quote.

On downspout spacing, Scope recommends one downspout per 30 linear feet of gutter, a default chosen to align with building code wherever possible. Check local code for the job in front of you.

Every report also carries a plain instruction: verify all dimensions and totals before purchasing materials. Treat it as standard practice: the report does the measuring, and your site visit confirms it.

How should you apply waste factor to gutter footage?

The waste table runs from 4% to 15% of total length. On the sample, the 10% row takes 471.5 feet to 518.7 feet. The project totals above the table are the measured lengths before any waste is added.

Which row you use depends on how you work: how many joints the house has, how you cut runs, and the stock lengths your supplier sells.

The table applies a single percentage to gutter and downspout combined. If you set waste differently for each, apply your own percentages to the gutter line and the downspout line separately instead of reading one row.

That's the same principle behind sizing every line of a roofing material order from its own measurement. Gutter footage is its own line, so it gets its own waste setting rather than a percentage borrowed from the shingle order.

Can you order gutters on their own or with the roof?

Yes. GutterScope can be ordered three ways:

  • On its own, for gutter-only jobs

  • As an add-on to a RoofScope order

  • As part of RoofScope+, which combines a RoofScope and a GutterScope

RoofScope+ fits the jobs where a roof replacement includes new gutters. You get the roof and the gutters in one order and one report. One Report. The Whole Exterior.

You can place orders through your account or by Text-to-Scope. GutterScope also works for new installs. If the house has no gutters today, the report measures along the eaves where the new system will go.

The jobs where a gutter report earns its place:

  • Roof replacements that include new gutters. Order RoofScope+ and the gutter takeoff arrives with the roof.

  • Gutter-only replacements. A standalone GutterScope covers the footage and fittings without a roof report.

  • New installs on houses with no gutters. The report measures the eaves where the system will go.

  • Properties with more than one structure. GutterScope covers multi-structure properties, such as a house with a detached garage.

Five checks before you build the gutter material list

Use these with any GutterScope report:

  1. Match the counts to the drawing. Corners and endcaps in the totals should line up with what the plan view shows. If a count looks off for the house, check the drawing before you order.

  2. Confirm size and profile on site. The report doesn't specify them, so settle both on your walk-through before the quote goes out.

  3. Set waste per line. Decide whether one percentage fits gutter and downspout together, or apply separate percentages to each footage line.

  4. Check downspout placement against spacing. Compare the drops on the plan view with Scope's one-per-30-feet recommendation and your local code.

  5. Verify before you buy. Follow the report's instruction to verify all dimensions and totals before purchasing materials.

Common questions about gutter measurement reports

Does a GutterScope report include gutter size?

No. It gives length and fittings. Gutter size and profile are chosen by the contractor on site.

Can I order a GutterScope for a house with no gutters?

Yes. The report measures along the eaves where the new gutters will go.

Is waste included in the project totals?

No. The totals are measured lengths. The waste table below them shows total length at 4% through 15%.

Can I get the roof and gutters in one report?

Yes. RoofScope+ combines a RoofScope and a GutterScope.

See a GutterScope report

See the full GutterScope sample on the GutterScope report page.

New to Scope? Book a demo to see how ordering works and what comes back. Already a customer? Reach out to your account manager or sales rep to add GutterScope to your next order.

written by RoofScope published on 11. 05. 2026

SHARE ON